Our Products

Item # MHV16-5K, Vertically Mounted Hydraulically Driven Air Conditioning and Heating Unit

The MacBone Series MHV16, 16,000 BTU/hr., air conditioning unit, is a side mounted, unitary, or self-contained unit, with a closed, precharged refrigeration circuit, driven by two, integral, hydraulic motors. Heating is derived from the circulation of hot engine coolant, engine oil or hydraulic oil through the unit. Heating capacity is 18,000 BTU/Hr. at a fluid flow rate of 1.0 GPM at 140° F, and cooling capacity is 16,000 BTU’s/HR. at input oil flow of 3.5 GPM at 2300 PSIG. The design concept is derived from the need for an operator’s cab air conditioning unit for industrial machines and vehicles where the unit can be quickly removed for service without involving the sealed refrigeration circuit. Cooling is provided by a thermostatically controlled refrigeration system, using refrigerant 134A. The condenser and evaporator blowers share a common shaft, driven by a hydraulic motor with sufficient power to produce substantial condenser air flow even with a filter on the outside coil, thus insuring reliable performance even in a heavily dust laden environment. Substantial power delivered to the inside air blower also assures delivery of full system capacity under all conditions. Induction of 10% outside air provides cab pressurization to exclude dust and other contaminants from entering the cab environment. An auxiliary outside air filter and cab pressurizer is available for additional pressurization.

Hydraulic drive input is from a dedicated pump driven by the vehicle's engine delivering from 3.50 to 6.00 GPM from 1000 PSIG at fan only and about 2300 PSIG with the compressor running for cooling. Or tap a compensated pressure source ranging from 2300 PSI to 4000 PSI, capable of a sustained flow rate of 3.50 GPM. Electrical input of 0.8 amps, at 12 or 24 VDC, is used to activate the compressor bypass valve, which allows for the compressor to be cycled by the thermostat. If the MacBone outside air filter / cab pressurizer is used, it will operate at an additional 4.0 amps at 12 or 24 VDC.

All side mount units utilize non-CFC, R-134A refrigerant, measure 28 x 20 3/8 x 10 inches high and weigh 104 pounds. Hydraulic lines are #6, supply and return. The motors have external case drains to protect the shaft seals. These are teed together inside the unit and require a #4 drain line back to tank up to 20’. Over 20’, use #6 drain line. Four mounting studs provide for quick removal for service or replacement. Recommended operating time before overhaul is 3,000 hours. Recommended unit life is four overhaul cycles.

The MHV16 series MacBone units are recommended for operator’s cabs in the range of 3’ wide x 5’ long, even if the cab is nearly all windows with only marginal insulation. With fewer windows and / or significant insulation, the MHV16 has proven to be satisfactory on cabs in the 4’ x 6’ range but, is not suitable for larger cabs unless the cab insulation is significant.
Specification
SizeMeasure 28 x 20-3/8 x 10 inches high
Length28 in
Width20-3/8 in
Height10 in
Weight (Basic Unit)104 lb
Cooling Capacity16,000 Btu/hr
Heating Capacity18,000 Btu/hr
Current4.0 A
Voltage12 V 24 V
Unit MotorA hydraulic motor with sufficient power to produce substantial condenser air flow even with a filter on the outside coil, thus insuring reliable performance even in a heavily dust laden environment. Substantial power delivered to the inside air blower also assures delivery of full system capacity under all conditions.
Hydraulic Lines#4 drain line back to tank up to 20’. Over 20’, use #6 drain line
RefrigerantR-134A
Shipping Length40 in
Shipping Width40 in
Shipping Height14 in
Shipping Weight 100 lb
Input Oil Flow3.5 GPM at 2300 PSIG
Recommended Cabinet Dimension3’ wide x 5’ long with only marginal insulation of nearly all windows 4’ wide x 6’ long with significant insulation with fewer windows